Audi 80/Avant (B4)

since 1991-1995 of release

Repair and car operation



Audi 80/Avant
+ Technical specification
+ Engines
+ System of production of the fulfilled gases
+ cooling System
+ Fuel tank and fuel pump
+ Air filter and airintaking channels
+ injection System
+ Coupling
+ Transmission and transmission
+ Suspension bracket and steering
+ Brake system
+ Anti-blocking system of brakes
+ Wheels and tires
+ Body electrosystem
+ ignition System
+ Lighting
+ Signalling devices
+ Devices and auxiliary devices
+ Heating and ventilation
- Body elements
   Front bumpers
   Forward part of the car
   Cowl
   Wings
   Moldings
   Doors
   External rear-view mirrors
   The forward and back flew down
   Trunk lid at a sedan
   Back door of the versatile person
   Rear bumper
   Movable hatch
   Pro-cleaning of openings for a water drain
   Control of anticorrosive protection of the bottom of a body
   Salon
   Seats
+ Search of malfunctions
+ Specifications




Salon

Removal of the left shelf

For shelf removal at the left to weaken bolts with 2 on 5. At installation to insert a shelf ahead in directing (the position 1 shows one of them).

The left lower part of a covering of the dashboard, integrated with a shelf, should be removed almost in all cases when access to a reverse side of the dashboard is necessary.

 PERFORMANCE ORDER

  1. Narrow face key to turn out four screws round a shelf.
  2. A few to cast away a shelf down and to extend to itself.
  3. At installation to insert a first line of a covering into both cars directing on the bottom and near pedals.
  4. Not too hardly to tighten screws.

Removal of a ware box

The ware box (2 and 3) is attached by the (1) loops to (arrow) dashboard. On an illustration the box is shown in unassembled form.


 PERFORMANCE ORDER

  1. To turn out at bottom edge of the dashboard both fixing the screw of a loop of a ware box.
  2. Slightly to wring out stoppers of a ware box inside and to cast away a ware box down.

Removal of the lower part of the central console

Removal of a back part of the central console: to remove a level (1), to disconnect a covering of the lever of the parking brake (3), to disconnect an earring (arrows) on the handle (2) from a clamp.


 PERFORMANCE ORDER

  1. To tighten the parking brake.
  2. To wring out a screw-driver fixing laying of a cover of the lever of the parking brake and to separate from a floor.
  3. In front slightly to raise a covering, to wring out a lever earring up and to extend the lever forward.
  4. To raise the decorative panel in front of the lever of the parking brake. Thus to hook the upper edge a small screw-driver.
  5. To turn out six fixing bolts, being under the panel.
  6. To remove a back ashtray.
  7. To turn out under an ashtray two six-sided bolts.
  8. To pull a console part for a first line up and to remove it in the direction forward over the lever of the parking brake.

Removal of a forward part of the central console

Removal of a forward part of the central console: to turn off a head of the lever of gear shifting (2), to weaken a bolt on a lever (1) casing. (3) – lobbies directing.


Shooters show on two bolts located in cut of the panel of heating which are necessary for weakening for removal of the central console.


 PERFORMANCE ORDER

  1. To disconnect a wire on "mass" of the accumulator.
  2. Completely to remove a back part of the central console.
  3. To remove the lever of gear shifting or the selector lever.
  4. To unscrew a bolt with a crosswise shliyets at back edge of the console and to remove a cover of the handle of gear shifting or a covering.
  5. To disconnect all three regulators of heating/ventilation.
  6. To unscrew two screws of the panel of heating and to remove it.
  7. At the cars equipped with the automatic conditioner, completely to remove a control panel.
  8. Below on the right and at the left in cut of the panel of heating to turn out on one screw.
  9. To wring out the console with an ashtray down, at body option with additional devices to remove in the direction down a narrow decorative plate.
  10. In the direction to disconnect the console from a control panel back.
  11. If necessary to disconnect wires.
  12. At installation directing on the dashboard and the central console should enter one into another.