Audi 80/Avant + Technical specification + Engines + System of production of the fulfilled gases + cooling System + Fuel tank and fuel pump + Air filter and airintaking channels + injection System + Coupling + Transmission and transmission + Suspension bracket and steering + Brake system + Anti-blocking system of brakes + Wheels and tires + Body electrosystem + ignition System + Lighting + Signalling devices + Devices and auxiliary devices + Heating and ventilation - Body elements Front bumpers Forward part of the car Cowl Wings Moldings Doors External rear-view mirrors The forward and back flew down Trunk lid at a sedan Back door of the versatile person Rear bumper Movable hatch Pro-cleaning of openings for a water drain Control of anticorrosive protection of the bottom of a body Salon Seats + Search of malfunctions + Specifications
|
Front bumpers
|
After a detachment of both parts of a front grille on the right and at the left in a bumper there are available both fixing bolts of a bumper. Now they can be turned out a key for an internal shestigrannik of 6 mm (shooter). |
|
The provision of an arm (1) fastening боковин a bumper can be changed after easing designated on an illustration shooters of bolts. |
|
Shooters show on boltovy connections which need to be weakened for removal of the bottom protection of a motor compartment. |
Removal
|
- To open a cowl.
- To remove the bottom protection of a motor compartment.
- To turn out in the middle behind a bumper from below a bolt with a crosswise shliyets.
- To disconnect and remove small plug-in elements of a front grille on the right and at the left below in a bumper.
- Under them there is a bolt with internal shestigranniky 6 mm. To turn out it.
- To remove plastic дюбели on the right and at the left on the back bottom ends of a bumper.
- To disconnect trailer parts of a bumper from body arms on a wing. For this purpose to press on lateral face of a bumper down, at the same time taking away it from a body.
- The ends of a bumper to hook over wheel niches and to remove in the direction forward.
- Now it is possible to remove a bumper in the direction forward.
- Cars with fog lights and/or turn indexes in a bumper: to disconnect cable connections to headlights in a bumper.
- Cars with faroomyvatel: to disconnect hoses from nozzles and to close them jams, not to devastate the tank.
- Slips in front on a bumper can be removed separately.
- The holder of registration plate in the middle of a bumper is in front fixed by two bolts.
- After removal of the holder of registration plate both боковины it is possible to remove from clamps separately by means of a flat plastic shpatel. For this purpose to press down both small fixing wedges, at the same time carefully separating a slip a hand.
|
|
Installation
|
- To connect wires and water hoses.
- Bumper at first to establish in arms.
- Now to enter боковины a bumper so that the bumper ends on faced facing of a wheel niche.
- Bokovina at first to hang for bottom edge on fastenings on a wing. Then to press a bumper sideways; thus the upper edge is fixed.
|
|
Alignment of bumpers
|
- To Prosl installations of a bumper should be checked, whether the crack between the metal strip everywhere is identical, located is slightly lower than headlights, and a bumper.
- Solving the size between bottom edge of a cowl and a bumper, however, is.
- This distance should make 6 mm.
- Otherwise it is necessary to remove once again a bumper, to weaken its arms and a little to shift them in longitudinal openings.
|
|
|
Help: plastic bumpers of Audi 80 practically without changes accept the primary form even after strong collisions. Therefore damages from road accident on the details located behind a bumper, can remain untouched. After collisions it is necessary to check (on existence or absence of damages) the following details: the forward party of a bumper under a slip (cross-section cracks), support behind a bumper, fixture of the case of a headlight, bottom edge of a cowl, a front grille. |
|
|