Audi 80/Avant + Technical specification + Engines + System of production of the fulfilled gases + cooling System + Fuel tank and fuel pump + Air filter and airintaking channels + injection System + Coupling + Transmission and transmission + Suspension bracket and steering + Brake system + Anti-blocking system of brakes + Wheels and tires + Body electrosystem + ignition System + Lighting + Signalling devices + Devices and auxiliary devices + Heating and ventilation - Body elements Front bumpers Forward part of the car Cowl Wings Moldings Doors External rear-view mirrors The forward and back flew down Trunk lid at a sedan Back door of the versatile person Rear bumper Movable hatch Pro-cleaning of openings for a water drain Control of anticorrosive protection of the bottom of a body Salon Seats + Search of malfunctions + Specifications
Диван для кухни со спальным местом купить в москве смотрите на www.divan-na-kuhniu.ru.
|
Back door of the versatile person
Drive of the lock of a back door of the version versatile person
|
For regulation of a back door from within the car it is necessary to insert a rasporny plate in thickness of 3 mm (in drawing it is allocated with red color) between the lock and a lock plate. |
Removal
|
- To remove a covering of a back door.
- To disconnect or remove electric plug connections, a hose of system of locks with the central management and a hose to a back nozzle of a stekloomyvatel.
- To open a back door and to prop up it.
- To wring out pneumatic springs from the top spherical pins (on a door).
- To turn off six-sided bolts above on a door loop. Two assistants should hold a door at the left and on the right.
- At installation to replace sealing washers between a loop and a door of a luggage compartment.
- To adjust the adjusting buffer of a back cover so that at the closed door between the buffer and a body there was a distance of 2-4 mm.
|
|
Removal of the cylinder of the lock
Removal of the cylinder of the lock occurs identically with described in the section «Removal of the lock of a luggage compartment» for a sedan.
Removal of a drive of the handle of a back door
Versatile person
|
- To remove a covering of a back door.
- To disconnect all connecting drafts from a handle drive.
- For this purpose to take aside lock brackets of connecting bent for to locks.
- To turn out two six-sided bolts with nuts.
- To take out a handle drive.
- Installation: in the middle and in parallel to enter a handle drive from a luggage compartment through a rectangular opening in the lower external part of a door.
- The stopper and sealing laying with a groove should adjoin to the lower external part of a door.
- To turn a handle drive until openings through passage and fixing openings in the lower part of a door will coincide.
- To tighten a handle drive a washer and a six-sided bolt (10 N • м).
- Again to hang all connecting drafts and to adjust their length.
- Connecting bent for to the lock cylinder: to establish the switching off lever in situation "is opened".
- To remove back the movable button in the middle of connecting draft so halves are freely inserted each other.
- In this situation to fix one in other carving parts of halves of draft and to stop the movable button.
- To adjust connecting bent for to locks of a back door – look the following section.
|
|
Removal of locks of a back door
Versatile person
|
- To remove an internal covering of a back door.
- To uncouple connecting drafts of locks, having taken aside lock brackets.
- In each lock to unscrew two six-sided nuts in a door frame.
- To take out the lock in the direction inside.
- Installation: slightly to tighten nuts of locks, to establish fastening points on the center.
- A few to weaken locking bracket (a part of the lock below on a body).
- To close a back door.
- From within a luggage compartment to enclose a rasporny plate (thickness of 3 mm) between the lock and a locking bracket.
- To close the lock in the second lock groove and to expose a back door.
- To adjust and fix gaps. The gap between the upper edge of a bumper and bottom edge of a back door should make 6,5 — 7,5 mm.
- To tighten six-sided nuts.
- To remove a rasporny plate; regulation of the lock of a back door is finished.
- Now it was necessary to establish length (built-in) draft of a drive: to remove back the movable button in the middle of both connecting drafts so that halves were freely inserted one into another.
- Lock latch at an open back door to put in situation "is closed" (the second lock groove).
- In this situation to fix carving parts of halves of draft one in another and to stop the movable button.
|
|
|
|